
Knob and Tube Wiring Replacement in Rockford, IL
Updated
Get a free quote
We reply with a price. Nothing is booked until you say yes.
Rather talk? Call (815) 420-4652 or text us.
Short answer
Want a price on knob-and-tube wiring replacement?
Call, text, or send the form. You get a written price back before any work is scheduled.
What knob-and-tube is and how to spot it
Knob-and-tube was the standard way to wire American houses from the 1880s into the 1930s and 1940s: single cloth-and-rubber insulated wires run separately, held off the framing by white porcelain knobs and passed through joists in porcelain tubes. Look in an unfinished basement ceiling or an attic for pairs of separate wires on porcelain. Rockford has a lot of housing from that era: 22.4% of the city's 67,423 housing units were built in 1939 or earlier, about 1 in 4, against a county-wide median build year of 1971 (Census Bureau). Census data shows age, not wiring, so the only way to know what is in a given house is to look.
Why it gets replaced
The wiring was not unsafe when it was installed. The problems are age and a century of changes: insulation that has gone brittle, splices added by previous owners, attic insulation blown over wires that were designed to shed heat into open air, and no ground wire, so no grounded outlets. Many homeowners insurers ask about it on older homes, and it is a routine finding in home inspections when a house sells. Two-prong outlets, a fuse box, and lights that dim when the furnace starts often come with it.
How the job is done in a plaster house
Most of the work is fishing new cable through existing walls and ceilings rather than tearing them out. Electricians work from the basement and attic, cut small openings at outlets, switches and a few strategic points, and patch them after. Plaster and lath is slower to fish and to patch than drywall, which is part of why older houses land at the high end of the per-square-foot range. A two-story house with an accessible basement and attic is the easiest case; a finished attic or a finished basement adds openings.
A full rewire usually comes with a new panel and service, because the old house is almost always on a small service or fuse box. It is also the time to add GFCI protection where the 2020 code requires it and AFCI protection on living-area circuits.
Permit and inspections in Rockford
A rewire is a permitted job in Rockford, with a rough-in inspection before walls, ceilings or soffits are covered and a final at the end, each requested at least one full business day ahead (City of Rockford). Under Rockford's 2020 NEC amendments, residential wiring can be NM cable in homes and residential buildings up to three floors (City of Rockford amendments). If you own and live in a single-family house, Rockford lets you do your own wiring with a permit, but any help you hire must be a Rockford-registered electrician (City of Rockford FAQ).
Room by room or all at once
A whole-house rewire done at once is the cheapest per square foot and the least disruptive overall. Doing it in phases (the kitchen and bath first, during a remodel, then bedrooms) spreads out the cost but repeats setup and patching. The national ranges for a whole-house rewire by size run from $8,000 to $30,000; the size table is on the cost page.
Sources: U.S. Census Bureau, ACS 2020-2024 5-year, via Census Reporter; City of Rockford, Electrical Permits; City of Rockford, Local Amendments to the 2020 NEC; City of Rockford, Construction FAQs (permit exemptions, homeowner work); IAEI Magazine, Residential changes for the 2020 NEC; National electrician cost guides (2026 data)
Where this is done
Knob-and-Tube Wiring Replacement in Rockford and the towns around it. Each town page has its own housing age, permit office and code edition; the rest are on the service area page.
Common questions
Knob-and-Tube Wiring Replacement: questions
How much does it cost to replace knob and tube wiring?
About $8 to $17 per square foot in national guides, and $8,000 to $30,000 for a whole-house rewire depending on size. Plaster walls and finished spaces raise it. See the cost page.
Is knob and tube wiring illegal in Illinois?
Illinois has no statewide electrical code and no rule forcing existing knob-and-tube out. New work has to meet the local code, and many insurers and home inspectors flag it.
How many Rockford homes have knob and tube?
No one counts it. What the Census does show is age: 22.4% of Rockford's housing was built in 1939 or earlier, the era when knob-and-tube was standard. Many of those houses have been partly or fully rewired since.
Will insurance cover a house with knob and tube wiring?
Some insurers decline or surcharge it; others ask for an electrician's evaluation. Ask your agent before you buy or renew, and keep the permit and inspection record after a rewire.
Can you rewire a house without tearing out walls?
Mostly. Electricians fish new cable from the basement and attic and cut small openings that get patched. Some openings are unavoidable, more in plaster and lath than drywall.
How long does it take to rewire a house?
A typical older single-family house takes days to a couple of weeks of electrical work, plus inspections and patching. The power is off only in sections while circuits are changed over.
Can I add insulation over knob and tube wiring?
Knob-and-tube was designed to shed heat into open air, which is why insulation over it is a common concern. Have it evaluated or replaced before insulating.
Other services
- Electrical repairsDead outlets, tripping breakers, flickering lights and warm switches, found and fixed.
- Emergency electricianSparking, burning smells, storm-damaged meters and power out to part of the house.
- Panel and service upgrades100 to 200 amp upgrades, fuse boxes, Federal Pacific and Zinsco panels.
- EV charger installationLevel 2 chargers, the panel check and ComEd's rebate.
- GeneratorsStandby generators and portable generator interlocks.
- Lighting and ceiling fansRecessed lights, fixtures, outdoor lighting and fans.
- Outlets and GFCINew outlets, GFCI protection, 240-volt outlets and circuits.
- Whole-house rewiringFull rewires for older houses and major remodels.
- Commercial electricianShops, offices and small commercial buildings.
Knob-and-Tube Wiring Replacement around Rockford
Tell us what you need and roughly how old the house is. We reply with a written price, and nothing starts until you agree to it.
