
Lighting and Ceiling Fan Installation in Rockford, IL
Updated
Get a free quote
We reply with a price. Nothing is booked until you say yes.
Rather talk? Call (815) 420-4652 or text us.
Short answer
Want a price on lighting and ceiling fans?
Call, text, or send the form. You get a written price back before any work is scheduled.
Recessed lighting
Most recessed lighting today is thin LED wafer or canless fixtures that need only a small hole and no housing above the ceiling, which makes retrofits in finished ceilings much easier than old cans. The price per light drops when several go in one room on one switch. Older Rockford houses with plaster and lath ceilings take more time to cut cleanly and to fish wire through, and an insulated attic above the top floor needs fixtures rated for contact with insulation. Six or more lights, or adding a new switch leg, usually means a new circuit or at least a load check.
Ceiling fans need a fan-rated box
A ceiling fan hangs and wobbles, so it has to be mounted on a box listed for fan support, not a light-fixture box held up by two small screws. Swapping a light for a fan where a rated box is already in the ceiling is the low end of the range. Adding a brace and a fan-rated box, or running a new switch leg for separate fan and light control, is the high end, about $350 to $700 in national guides. Rockford's permit exemption covers replacing a fan or light fixture weighing less than 35 pounds as long as the wiring and junction box are not changed (City of Rockford FAQ); a new box is a change.
Fixtures, under-cabinet and outdoor lights
Replacing a fixture on an existing box is the simplest lighting job. Under-cabinet lighting in a kitchen usually needs a new switched feed and, if it plugs in, a receptacle inside the cabinet. Outdoor lights on a house or garage need fixtures rated for wet locations and weatherproof boxes, and buried lines to a post light or detached garage have burial-depth and conduit rules that the inspector checks before the trench is backfilled. Rockford schedules that as its underground inspection, before anything is covered (City of Rockford).
Commercial lighting
Shops and offices around Rockford mostly run drop ceilings with 2-by-4 or 2-by-2 fixtures, many still fluorescent. Retrofitting to LED panels or kits is the most common commercial lighting job. Commercial wiring in Rockford, Loves Park, Machesney Park and Belvidere goes in conduit or metal-clad cable: the regional amendments limit NM (Romex) cable to residential buildings of three floors or less. More on commercial work is in the commercial electrician section of the homepage.
Dimmers, switches and smart controls
LED fixtures need LED-compatible dimmers, or they flicker and buzz. Smart switches often need a neutral wire in the switch box, which many pre-1980 Rockford houses don't have at every switch; the electrician checks before you buy. Three-way and four-way switching (a light controlled from two or three places) adds wire runs and time.
Sources: City of Rockford, Construction FAQs (permit exemptions, homeowner work); City of Rockford, Electrical Permits; City of Rockford, Local Amendments to the 2020 NEC; City of Loves Park, Ord. 4678-25 (2020 NEC); National electrician cost guides (2026 data)
Where this is done
Lighting and Ceiling Fans in Rockford and the towns around it. Each town page has its own housing age, permit office and code edition; the rest are on the service area page.
Common questions
Lighting and Ceiling Fans: questions
How much does it cost to install recessed lighting?
Typical U.S. ranges are $125 to $400 per recessed light, less each when six or more go in one room. Plaster ceilings, long runs and a new circuit raise it. See the cost page.
How much does it cost to install a ceiling fan?
About $150 to $600 in national guides. A fan-rated box already in place is the low end; a new box, brace and wiring is the high end.
Do I need a permit to replace a light fixture in Rockford?
Usually not. Rockford exempts replacing light fixtures and ceiling fans weighing less than 35 pounds when the wiring and junction box are not altered. New fixtures, boxes and circuits need a permit.
Can I put a ceiling fan where a light is?
Only if the box is rated for fan support. Many old light boxes are not. The fix is a fan-rated box with a brace between the joists.
Why do my LED lights flicker on a dimmer?
Most often the dimmer was made for incandescent bulbs. An LED-rated dimmer matched to the fixtures usually fixes it. Flicker with no dimmer can mean a loose connection, which is worth having checked.
Do smart switches work in older houses?
Many smart switches need a neutral wire in the switch box. Houses wired before the 1980s often have only a hot and a switched leg at the switch. Some models work without a neutral; otherwise the box needs rewiring.
What lighting work needs an inspection in Rockford?
New wiring gets a rough-in inspection before walls or ceilings are covered and a final at the end, requested at least one full business day ahead. Underground runs get their own inspection before backfill.
Other services
- Electrical repairsDead outlets, tripping breakers, flickering lights and warm switches, found and fixed.
- Emergency electricianSparking, burning smells, storm-damaged meters and power out to part of the house.
- Panel and service upgrades100 to 200 amp upgrades, fuse boxes, Federal Pacific and Zinsco panels.
- EV charger installationLevel 2 chargers, the panel check and ComEd's rebate.
- GeneratorsStandby generators and portable generator interlocks.
- Outlets and GFCINew outlets, GFCI protection, 240-volt outlets and circuits.
- Knob-and-tube replacementOld cloth and porcelain wiring replaced in older houses.
- Whole-house rewiringFull rewires for older houses and major remodels.
- Commercial electricianShops, offices and small commercial buildings.
Lighting and Ceiling Fans around Rockford
Tell us what you need and roughly how old the house is. We reply with a written price, and nothing starts until you agree to it.
